Xiaomi Router Modelleri ve OpenWrt Firmware [ANA KONU] - OpenWrt 24.10.1 Yayınlandı! (319. sayfa)

millenicomdan her saman uzak durmakta fayda var

teşekkür ederim

Arkadaşlar Openwrt olur merlin, ddwrt, tomatowrt olur router tavsiyelerinizi bekliyorum

oyun odaklı kullanacağım sqm benim için yeterli

https://forum.donanimhaber.com/mesaj/yonlen/153645736

Buradaki anlatımı kullanarak sonunda bende çalıştırdım tv plus'ı. Elinize emeğinize sağlık @androidmeda

Meğer buga girmiş cihaz. Cihaza arkasından reset atınca çalıştı. 2 gündür boşa uğraşıyormuşum.

https://forum.donanimhaber.com/mesaj/yonlen/156179654 @Kolonyalı

https://forum.donanimhaber.com/mesaj/yonlen/154423967 @kowalski61

Ancak yukarıda alıntıladığım arkadaşların sıkıntısı mevcut. Yayın 5-6 saniye normal, sonra 10-15 saniye takıla takıla ilerliyor sonra 5-6 saniye normal. Bu şekilde döngü halinde gidiyor.

Başka yaşayan oldu mu bu durumu?

@0ldskool ve @androidmeda Üstatların tavsiyesi olur muydu?

@Miui Konudan takip ettiğim kadarıyla sizde de mir4a vardı sanırım. Siz çözdünüz mü?

İşin enteresan yanı, tv+ üzerinden dizi film ya da youtube izlerken sorun yok, tv kanalları takıla takıla oynuyor.

Bir de bir sorun daha var. 3. adımda route için gateway giriyoruz. O bende ne koşulda bilmiyorum ama sürekli değişiyor. Tv+ ı açınca zaman senkronizasyon hatası veriyor. Bakıyorum nexthop daki ip değişmiş, düzeltiyorum. Tv+ kapatıp açsam da çözüm olmuyor. Reset atıyorum çalışıyor.

Config dosyaları şu şekilde:

35 mbit kullanıyorsunuz ve bir arayıştasınız anladığım kadarıyla kriterleriniz

-tek cihaz olsun

-çekim gücü iyi olsun köşe odalarda çeksin

-ucuz olsun

böyle bir modem var mı bilmiyorum o kadar araştırdım görmedim duymadım

Benimki hobi diyelim.35 mbps vdsl şu an ihtiyacımı fazlasıyla yetiyor.Uğraşmak hoşuma gidiyor.İlgimi çeken farklı cihazları alıp kullanıp test sonuçlarımı yazıyorum.Bende yeni şeyler öğrenmiş oluyorum.Belki bazı arkadaşların işine yarar.En iyi verimi zyxell 3625 de aldım.2.4 ghz evin her köşesinde rahat çekiyordu.İnanılmaz bir wifi çekimi vardı.Duramadım satıp denemek için Dx3200 aldım.Donanımı çok güçlü ama wifisi 3625 gibi değil.Tekrar 3625 aldım.Xiamio 4a giga routerde var.Üst model pahalı modellei değilde uygun fiyatlı mikrotik,fritzbox vb kullanmadığım modemleride merak ediyorum.

hocam uygun fiyat olayı kalmadı bence onu unutun

yerinizde olsam güzel bir router alır openwrt kurar fiberde kullanırdım tek cihaz kusursuz internet mis gibi başka alternatifiniz yok

hem iyi çeksin hem de ucuz olsun diyen çoğu wifi 6 router kullanan openwrt kullanıcısı bunu kullanıyor

bu fiyatın altına bu kalitede router bulamazsınız daha ucuzu yok zaten amazon satıyor

amazon.com

Dynalink WiFi 6 AX3600 Router (DL-WRX36), Dual Band, 8-Stream WiFi Router, Wireless Speed Up to 3.6Gbps, MU-MIMO, 2.5G WAN Port, 4 Gigabit LAN Ports, for Home & Gaming (1 Pack)

https://www.amazon.com/Dynalink-DL-WRX36-8-Stream-Wireless-3-6Gbps/dp/B096K9SVCT

Hocam router ile ilgili türkçe inceleme videosuda göremedim, forumda kullanıcı yorumlarınıda varsa link atarmısınız?

https://forum.openwrt.org/t/whats-your-favorite-enthusiast-lede-openwrt-device/4477

https://forum.openwrt.org/t/802-11ax-routers/10484

https://forum.openwrt.org/t/best-consumer-router-for-200-mbps-isp/158213

arama kısmına wrx36 yazarak ulaşabilirsiniz alternatif olarak uğraşmak istemezseniz TP-LINK deco mesh sistemlerine göz atabilirsiniz

köşe odalarda çekmeme sorununu çözer ama yine dediğim gibi 35 mbit vdsl kullanmaya devam edecekseniz masrafa girmeyin derim fiber için değer

akakce.com

Deco > TP-Link Fiyatları | En Ucuzu Akakçe

https://www.akakce.com/arama/?q=deco&f=140497&s=1

Bendeki takılma sorunu araştırmama göre igmpproxy ile alakalı sanırım.

Loglarda da pek bir şey yok aslında.

debug modunda şöyle çalışıyor igmpproxy:

Kod 
Yığını:
Searching for config file at '/var/etc/igmpproxy.conf'
 Config: Quick leave mode enabled.
 Config: Got a phyint token.
 Config: IF: Config for interface br-lan.
 Config: IF: Got downstream token.
 Config: IF: Got ratelimit token '0'.
 Config: IF: Got threshold token '1'.
 IF name : br-lan
 Next ptr : 0
 Ratelimit : 0
 Threshold : 1
 State : 2
 Allowednet ptr : 0
 Config: Got a phyint token.
 Config: IF: Config for interface wan.103.
 Config: IF: Got upstream token.
 Config: IF: Got ratelimit token '0'.
 Config: IF: Got threshold token '1'.
 Config: IF: Got altnet token 0.0.0.0/0.
 Config: IF: Altnet: Parsed altnet to default.
 IF name : wan.103
 Next ptr : 0
 Ratelimit : 0
 Threshold : 1
 State : 1
 Allowednet ptr : 77db8bb0
 buildIfVc: Interface lo Addr: 127.0.0.1, Flags: 0x0049, Network: 127/8
 buildIfVc: Interface br-lan Addr: 192.168.1.1, Flags: 0x1043, Network: 192.168.1/24
 buildIfVc: Interface wan.103 Addr: 100.112.86.44, Flags: 0x1043, Network: 100.112.84/22
 buildIfVc: Interface pppoe-wan Addr: 10.100.205.39, Flags: 0x10d1, Network: 10.100.0.1/32
 Found config for br-lan
 Found config for wan.103
 adding VIF, Ix 0 Fl 0x0 IP 0x0101a8c0 br-lan, Threshold: 1, Ratelimit: 0
         Network for [br-lan] : 192.168.1/24
 Found upstrem IF #0, will assing as upstream Vif 2
 adding VIF, Ix 1 Fl 0x0 IP 0x2c567064 wan.103, Threshold: 1, Ratelimit: 0
         Network for [wan.103] : 100.112.84/22
         Network for [wan.103] : default
 Got 262144 byte buffer size in 0 iterations
 Joining all-routers group 224.0.0.2 on vif 192.168.1.1
 Joining group 224.0.0.2 on interface br-lan
 Joining all igmpv3 multicast routers group 224.0.0.22 on vif 192.168.1.1
 Joining group 224.0.0.22 on interface br-lan
 SENT Membership query   from 192.168.1.1     to 224.0.0.1
 Sent membership query from 192.168.1.1 to 224.0.0.1. Delay: 10
 Created timeout 1 (#0) - delay 10 secs
 (Id:1, Time:10) 
 Created timeout 2 (#1) - delay 21 secs
 (Id:1, Time:10) 
 (Id:2, Time:21) 
 RECV Membership query   from 192.168.1.1     to 224.0.0.1
 RECV V2 member report   from 192.168.1.1     to 224.0.0.2
 The IGMP message was from myself. Ignoring.
 RECV V2 member report   from 192.168.1.1     to 224.0.0.22
 The IGMP message was from myself. Ignoring.
 RECV V2 member report   from 192.168.1.1     to 224.0.0.106
 The IGMP message was from myself. Ignoring.
 About to call timeout 1 (#0)
 Aging routes in table.
 
 Current routing table (Age active routes):
 -----------------------------------------------------
 No routes in table...
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.130   to 239.255.255.250
 Should insert group 239.255.255.250 (from: 192.168.1.130) to route table. Vif Ix : 0
 No existing route for 239.255.255.250. Create new.
 No routes in table. Insert at beginning.
 Inserted route table entry for 239.255.255.250 on VIF #0
 Joining group 239.255.255.250 upstream on IF address 100.112.86.44
 Joining group 239.255.255.250 on interface wan.103
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 239.255.255.250, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.130   to 233.26.166.30
 Should insert group 233.26.166.30 (from: 192.168.1.130) to route table. Vif Ix : 0
 No existing route for 233.26.166.30. Create new.
 Found existing routes. Find insert location.
 Inserting at beginning, before route 239.255.255.250
 Inserted route table entry for 233.26.166.30 on VIF #0
 Joining group 233.26.166.30 upstream on IF address 100.112.86.44
 Joining group 233.26.166.30 on interface wan.103
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 239.255.255.250, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.130   to 225.0.71.1
 Should insert group 225.0.71.1 (from: 192.168.1.130) to route table. Vif Ix : 0
 No existing route for 225.0.71.1. Create new.
 Found existing routes. Find insert location.
 Inserting at beginning, before route 233.26.166.30
 Inserted route table entry for 225.0.71.1 on VIF #0
 Joining group 225.0.71.1 upstream on IF address 100.112.86.44
 Joining group 225.0.71.1 on interface wan.103
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 About to call timeout 2 (#0)
 SENT Membership query   from 192.168.1.1     to 224.0.0.1
 Sent membership query from 192.168.1.1 to 224.0.0.1. Delay: 10
 Created timeout 3 (#0) - delay 10 secs
 (Id:3, Time:10) 
 Created timeout 4 (#1) - delay 21 secs
 (Id:3, Time:10) 
 (Id:4, Time:21) 
 RECV Membership query   from 192.168.1.1     to 224.0.0.1
 RECV V2 member report   from 192.168.1.130   to 233.26.166.30
 Should insert group 233.26.166.30 (from: 192.168.1.130) to route table. Vif Ix : 0
 Updated route entry for 233.26.166.30 on VIF #0
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.1     to 224.0.0.22
 The IGMP message was from myself. Ignoring.
 RECV V2 member report   from 192.168.1.1     to 224.0.0.2
 The IGMP message was from myself. Ignoring.
 About to call timeout 3 (#0)
 Aging routes in table.
 
 Current routing table (Age active routes):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.130   to 239.255.255.250
 Should insert group 239.255.255.250 (from: 192.168.1.130) to route table. Vif Ix : 0
 Updated route entry for 239.255.255.250 on VIF #0
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.130   to 225.0.71.1
 Should insert group 225.0.71.1 (from: 192.168.1.130) to route table. Vif Ix : 0
 Updated route entry for 225.0.71.1 on VIF #0
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.1     to 224.0.0.106
 The IGMP message was from myself. Ignoring.
 About to call timeout 4 (#0)
 SENT Membership query   from 192.168.1.1     to 224.0.0.1
 Sent membership query from 192.168.1.1 to 224.0.0.1. Delay: 10
 Created timeout 5 (#0) - delay 10 secs
 (Id:5, Time:10) 
 Created timeout 6 (#1) - delay 115 secs
 (Id:5, Time:10) 
 (Id:6, Time:115) 
 RECV Membership query   from 192.168.1.1     to 224.0.0.1
 RECV V2 member report   from 192.168.1.1     to 224.0.0.22
 The IGMP message was from myself. Ignoring.
 RECV V2 member report   from 192.168.1.130   to 239.255.255.250
 Should insert group 239.255.255.250 (from: 192.168.1.130) to route table. Vif Ix : 0
 Updated route entry for 239.255.255.250 on VIF #0
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.130   to 233.26.166.30
 Should insert group 233.26.166.30 (from: 192.168.1.130) to route table. Vif Ix : 0
 Updated route entry for 233.26.166.30 on VIF #0
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:1, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.1     to 224.0.0.2
 The IGMP message was from myself. Ignoring.
 RECV V2 member report   from 192.168.1.1     to 224.0.0.106
 The IGMP message was from myself. Ignoring.
 About to call timeout 5 (#0)
 Aging routes in table.
 
 Current routing table (Age active routes):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 RECV V2 member report   from 192.168.1.130   to 225.0.71.1
 Should insert group 225.0.71.1 (from: 192.168.1.130) to route table. Vif Ix : 0
 Updated route entry for 225.0.71.1 on VIF #0
 
 Current routing table (Insert Route):
 -----------------------------------------------------
 #0: Dst: 225.0.71.1, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #1: Dst: 233.26.166.30, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 #2: Dst: 239.255.255.250, Age:2, St: I, OutVifs: 0x00000001, dHosts: yes
 -----------------------------------------------------
 About to call timeout 6 (#0)
 SENT Membership query   from 192.168.1.1     to 224.0.0.1
 Sent membership query from 192.168.1.1 to 224.0.0.1. Delay: 10
 Created timeout 7 (#0) - delay 10 secs
 (Id:7, Time:10) 
 Created timeout 8 (#1) - delay 115 secs
 (Id:7, Time:10) 
 (Id:8, Time:115) 
 RECV Membership query   from 192.168.1.1     to 224.0.0.1
 RECV V2 member report   from 192.168.1.130   to 225.0.71.1
 Should insert group 225.0.71.1 (from: 192.168.1.130) to route table. Vif Ix : 0
 Updated route entry for 225.0.71.1 on VIF #0

Bu konuda tavsiyeleriniz olur muydu @0ldskool @androidmeda . Igmpproxy servisini kapatmak ya da açmak etki etmiyor.

kurulum çok kolay aslında. iki dosya yüklüyorsun o kadar. sonrasında sadece güncellemeler için sysupgrade.bin dosyalarını yükseltmen gerekiyor. gerçi bu cihazın openwrt yazılımı generic ve epenwrt bu modelin de yer aldığı ax qualcom yonga setlerinde hedef düşürme yoluna gitmiş. galiba orjinal sürümü kullanıyor olmak en iyi bir seçenek görünüyor.