bugun 2gb micro sd sandisk aldım önce bi telefonda formatladım telefonda kartı görüyor...
dedim biraz mp3 atayım karta card reader micro sd kart takıldığını görüyor ama içine girmeme ve format atmama izin vermiyor boyut olarakda 0 kb görüyor.
card reader aynı yuvadan beslenen diğer bir sd kartımı hemen görüyor ve dilediğim işlemi yapabiliyorum.
micro sd adaptörleri yeni ikiside ayrıca adaptör kenarında bulunan lock u 2 türlü denedim yinede yemedi.
neden olabilir fikirlerinizi bekliyorum..
Kartın şifresi varsa kaldırıp öyle deneyin..
Bende de 4gb micro sd var. 6500s ile kullanıyorum. Aldığımdan beri 5 farklı marka laptop 7 farklı masaüstü pc ve 12 değişik adaptör kullandım. Hiçbiri de görmedi. Sizce bu bilgisayarlar mı bozukda görmüyor. Yoksa bu telefon türünün tek örneği olupda sadece kendi açabiliyor.
Telefonda tıkır tıkır çalışıyor ve sadece telefona takılıykenusb kablosuyla pcye bağlayınca görüyor. Onun dışında banamasın demiyor. Sorun kartta mı sizce?
4 GB'lık kart aslında olması gerektiği gibi microSDHC değildir microSD'dir, bu nedenle görmüyor olabilir.
Devices that use SD cards identify the card by requesting a 128-bit identification string from the card. For standard-capacity SD cards, 12 of the bits are used to identify the number of memory clusters (ranging from 1 to 4096) and 3 of the bits are used to identify the number of blocks per cluster (which decode to 4, 8, 16, 32, 64, 128, 256 or 512 blocks per cluster).
In older 1.x implementations the standard capacity block was exactly 512 bytes. This gives 4096 x 512 x 512 = 1 gigabyte of storage memory. A later revision of the 1.x standard allowed a 4-bit field to indicate 1024 or 2048 bytes per block instead, yielding more than 1 gigabyte of memory storage. Devices designed before this change may incorrectly identify such cards, usually by misidentifying a card with lower capacity than is the case by assuming 512 bytes per block rather than 1024 or 2048.
For the new SDHC high capacity card (2.0) implementation, 22 bits of the identification string are used to indicate the memory size in increments of 512 KBytes. Currently 16 of the 22 bits are allowed to be used, giving a maximum size of 32 GB. All SDHC 4-GB and larger cards must be 2.0 implementations. Two bits that were previously reserved and fixed at 0 are now used for identifying the type of card, 0=standard, 1=HC, 2=reserved, 3=reserved. Non-HC devices are not programmed to read this code and therefore cannot correctly read the identification of the card.
All SDHC readers work with standard SD cards.
Many older devices will not accept the 2 or 4 GB size even though it is in the revised standard. The following statement is from the SD association specification: "To make 2 GByte card, the Maximum Block Length (READ_BL_LEN=WRITE_BL_LEN) shall be set to 1024 bytes. However, the Block Length, set by CMD16, shall be up to 512 bytes to keep consistency with 512 bytes Maximum Block Length cards (Less than and equal 2 Gbyte cards)."
yeni mesaja git
Yeni mesajları sizin için sürekli kontrol ediyoruz, bir mesaj yazılırsa otomatik yükleyeceğiz.Bir Daha Gösterme