Şimdi Ara

Bi - wire bağlantı

Bu Konudaki Kullanıcılar:
2 Misafir - 2 Masaüstü
5 sn
50
Cevap
1
Favori
3.126
Tıklama
Daha Fazla
İstatistik
  • Konu İstatistikleri Yükleniyor
0 oy
Öne Çıkar
Sayfa: 1
Giriş
Mesaj
  • Aşağıda resmi bulunan amfi (Vincent SV236 MKII) ve hoparlör (Klipsch RF7II) için bi-wire ve bi-amp bağlantısı nasıl yaparım. Ayrıca amfinin sağ ve sol için ikişer adet çıkış bulunmakta, tek çıkışından değil iki ayrı çıkışından 2 ayrı kabloyu hoparlörün iki ayrı girişine bağlayabiliyor muyum bağlarsam verim alabiliyor muyum ve bu yaptığım bağlantının ismi nedir?


     Bi - wire bağlantı



  • Al abicim bi amp
    http://lib.store.yahoo.net/lib/fluance/biamp

    < Bu ileti mobil sürüm kullanılarak atıldı >
  • Bu linkte şöyle anlatmışlar:

    http://www.oregondv.com/Audio_FAQ_Bi-Wire_Bi-amp%20.htm

    Biwire anlatımında tek ampli gösterilmiş.

    Bi-amp anlatımında çift ampli gösterilmiş.

    Haa bu arada ben tek ampli ve iki farklı çıkış ile bi-amp yaparım derseniz ne derim hiç bir şey demem ve saygı duyarım o da bi-amp benzeri bir uygulama olur ama yaptığınız uygulama esas literatürdeki bi-amp değildir pasif bi-amping dir ne kadar işe yarar tartışılır belki bir miktar yarar bununla ilgili bir örnek vermek gerekirse de zaten akıp giden üzerinde belli bir trafik olan bir yolu yine aynı trafik koşullarında aynı yoğunlukta iki şeritten tek şerite düşürüp iki farklı yol yapmak gibi bir şey bu....Oysa diğerinde aynı trafiği şerit düşürmeden iki ayrı ve yine iki şeritli yola aktarıyorsunuz ampli başına düşen yük azalıyor ve besleme artıyor...


    Hatta linke tıklamak istemeyenler için linkteki bi-amp açıklaması şöyle:

    How do I bi-amp?
    Bi-amping is similar to bwiring, but involves separate amplifiers: one for the woofer and one for the midrange/tweeter. Passive bi-amping involves a direct hookup between each amplifier and the speaker terminals. True bi-amping involves hooking the preamp to an electronic crossover that replaces the passive crossover network in the speaker. The active crossover then connects to multiple power amplifiers. For example, one amplifier for the woofer and another amplifier for the mid/highs. The internal speaker crossover network must be eliminated. bi-amping is a difficult and expensive approach that is not typically employed



    < Bu mesaj bu kişi tarafından değiştirildi atalayalper -- 1 Aralık 2012; 3:32:12 >
  • quote:

    Orijinalden alıntı: eraycelik80

    Değmez ustat

    Teşekkürler.
    Bu yorumundan sonra olumsuz yön bulmaya çalışan araştırma yaptım ve Şuna rastladım.

    quote:

    ....As we have seen, the key part of the equation is the electronic crossover. Splitting the signal at line level allows us to bypass the lowly passive network. So, buy another amp, an electric crossover and you are off to races. Ah, but it's not that simple. Now comes the task of calibrating the crossover to your speakers; making sure that the drivers are sent the specific frequencies their designers intended, and that slopes (the rate at which the transition between the frequencies occur, and how much they overlap) are correctly set. These adjustments are key to not only optimum performance, but system safety; operating a driver beyond its range will likely result in its failure. Maybe you've read the book, "Poof the Mangled Driver"?

    Ok, so what about just using two amplifiers and forgetting about the electronic crossover? Simply using two amplifiers is not true bi-amping and does not offer the same advantages; we still face the limitations of the passive crossover. What about the notion that bi-amping reduces stress on the amplifiers since they are powering only limited frequency ranges? That would be true in a true bi-amp configuration where the frequencies are split ahead of the amplifiers, but in a passive environment both amplifiers receive a full range signal from the preamp and dump that power into the speakers, regardless of whether one is connected to the tweeter or woofer inputs. The only benefit (and it marginal at best) is simply the additional power offered by the second amp.....


    Özetle;
    Eğer kaynaktan çıkışta elektronik xover kullanılmıyorsa, kaynaktan amfiye girip ayrı kanallarda yükseltilen sinyal > pasif xover bulunan bi-amp hoparlörde çok da fayda sağlamaz.
    Sağlanan tek marjinal fayda, tek kanal yerine 2 kanal gücünün ayrı ayrı hoparlöre aktarılmasından ibarettir.



    < Bu mesaj bu kişi tarafından değiştirildi meke -- 20 Ocak 2016; 23:34:31 >
  • 
Sayfa: 1
- x
Bildirim
mesajınız kopyalandı (ctrl+v) yapıştırmak istediğiniz yere yapıştırabilirsiniz.